View LD1084_128480.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LD1084 SERIES
5A LOW DROP POSITIVE VOLTAGE REGULATOR ADJUSTABLE AND FIXED
s s
s
s
s s
s
s
TYPICAL DROPOUT 1.3V (AT 5A) THREE TERMINAL ADJUSTABLE OR FIXED OUTPUT VOLTAGE 1.5, 1.8V, 2.5V, 2.85V, 3.3V, 3.6V, 5V, 8V, 9V, 12V. GUARANTEED OUTPUT CURRENT UP TO 5A OUPUT TOLERANCE 1% AT 25C AND 2% IN FULL TEMPERATURE RANGE INTERNAL POWER AND THERMAL LIMIT WIDE OPERATING TEMPERATURE RANGE -40C TO 125C PACKAGE AVAILABLE : TO-220, D2PAK, D2PAK/A PINOUT COMPATIBILITY WITH STANDARD ADJUSTABLE VREG
D2PAK
TO-220
D2PAK/A
DESCRIPTION The LD1084 is a LOW DROP Voltage Regulator able to provide up to 5A of Output Current. Dropout is guaranteed at a maximum of 1.5V at the maximum output current, decreasing at lower loads. The LD1084 is pin to pin compatible with the older 3-terminal adjustable regulators, but has better performances in term of drop and output tolerance .
A 2.85V output version is suitable for SCSI-2 active termination. Unlike PNP regulators, where a part of the output current is wasted as quiescent current, the LD1084 quiescent current flows into the load, so increase efficiency. Only a 10F minimum capacitor is need for stability. The device is supplied in TO-220, D2PAK and D2PAK/A. On chip trimming allows the regulator to reach a very tight output voltage tolerance, within 1% at 25C.
SCHEMATIC DIAGRAM
May 2003
1/18
LD1084 SERIES
ABSOLUTE MAXIMUM RATINGS
Symbol VI IO PD Tstg Top DC Input Voltage Output Current Power Dissipation Storage Temperature Range Operating Junction Temperature Range Parameter Value 30 Internally Limited Internally Limited -55 to +150 -40 to +125 Unit V mA mW C C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied.
THERMAL DATA
Symbol Rthj-case Rthj-amb Parameter Thermal Resistance Junction-case Thermal Resistance Junction-ambient TO-220 3 50 D2PAK 3 62.5 Unit C/W C/W
APPLICATION CIRCUITS
R2 VO = VREF (1 + ) R1
CONNECTION DIAGRAM (top view)
TO-220
D2PAK
D2PAK/A
2/18
LD1084 SERIES
ORDERING CODES
TYPE LD1084V15 LD1084V18 LD1084V25 LD1084V28 LD1084V33 LD1084V36 LD1084V50 LD1084V80 LD1084V90 LD1084V120 LD1084V D2PAK (*) LD1084D2T15 LD1084D2T18 LD1084D2T25 LD1084D2T28 LD1084D2T33 LD1084D2T36 LD1084D2T50 LD1084D2T80 LD1084D2T90 LD1084D2T120 LD1084D2T D2PAK/A LD1084D2M15 LD1084D2M18 LD1084D2M25 LD1084D2M28 LD1084D2M33 LD1084D2M36 LD1084D2M50 LD1084D2M80 LD1084D2M90 LD1084D2M120 LD1084D2M OUTPUT VOLTAGE 1.5 V 1.8 V 2.5 V 2.85 V 3.3 V 3.6 V 5.0 V 8.0 V 9.0 V 12.0 V ADJ
(*) Available in Tape & Reel with the suffix "R" for fixed versions and "-R" for adjustable version
LECTRICAL CHARACTERISTICS OF LD1084#15 (VI=4.5V, C I = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA Test Conditions TJ = 25C IO = 0 to 5A VI = 3.1 to 30V (note 1) IO = 0 mA VI = 3.1 to 18V TJ = 25C IO = 0 mA IO = 0 to 5A IO =5 A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, IO = 5A VI = 6.8 3V TA = 25C f =10Hz to 10KHz 60 5.5 0.5 VI = 3.1 to 15V IO = 0 to 5A TJ = 25C Min. 1.485 1.47 Typ. 1.5 1.5 0.5 0.1 3 7 1.3 5 6.5 0.7 0.003 75 0.003 0.5 0.5 0.015 Max. 1.515 1.53 6 6 15 20 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % %
TA = 125C
1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
3/18
LD1084 SERIES
ELECTRICAL CHARACTERISTICS OF LD1084#18 (VI=4.8V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA IO = 0 mA IO = 0 mA Test Conditions TJ = 25C VI = 3.4 to 18V VI = 3.4 to 15V TJ = 25C IO = 0 to 5A VI = 3.4 to 30V (note 1) Min. 1.782 1.764 Typ. 1.8 1.8 0.5 0.1 3 7 1.3 5 5.5 0.5 60 6.5 0.7 0.003 75 0.003 0.5 0.5 0.015 Max. 1.818 1.836 6 6 15 20 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % %
IO = 0 to 5A TJ = 25C IO = 0 to 5A IO =5 A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, IO = 5A VI = 6.8 3V TA = 25C f =10Hz to 10KHz
TA = 125C
1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
ELECTRICAL CHARACTERISTICS OF LD1084#25 (VI=5.5V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA Test Conditions TJ = 25C IO = 0 to 5A VI = 4.1 to 30V (note 1) IO = 0 mA VI = 4.1 to 18V TJ = 25C IO = 0 mA IO = 0 to 5A IO =5 A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, IO = 5A VI = 7.5 3V TA = 25C f =10Hz to 10KHz 60 5.5 0.5 VI = 4.1 to 18V IO = 0 to 5A TJ = 25C Min. 2.475 2.45 Typ. 2.5 2.5 0.5 0.1 3 7 1.3 5 6.5 0.7 0.003 72 0.003 0.5 0.5 0.015 Max. 2.525 2.55 6 6 15 20 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % %
TA = 125C
1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
4/18
LD1084 SERIES
ELECTRICAL CHARACTERISTICS OF LD1084#285 (VI=5.85V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA Test Conditions TJ = 25C IO = 0 to 5A VI = 4.5 to 30V (note 1) IO = 0 mA VI = 4.5 to 18V TJ = 25C IO = 0 mA IO = 0 to 5A IO =5 A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, IO = 5A VI = 7.85 3V TA = 25C f =10Hz to 10KHz 60 5.5 0.5 VI = 4.5 to 18V IO = 0 to 5A TJ = 25C Min. 2.821 2.793 Typ. 2.85 2.85 0.5 0.1 3 7 1.3 5 6.5 0.7 0.003 72 0.003 0.5 0.5 0.015 Max. 2.879 2.907 6 6 15 20 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % %
TA = 125C
1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
ELECTRICAL CHARACTERISTICS OF LD1084#33 (VI=6.3V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA Test Conditions TJ = 25C IO = 0 to 5A VI = 4.9 to 30V (note 1) IO = 0 mA VI = 4.9 to 18V TJ = 25C IO = 0 mA IO = 0 to 5A IO =5 A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, IO = 5A VI = 8.3 3V TA = 25C f =10Hz to 10KHz 60 5.5 0.5 VI = 4.9 to 18V IO = 0 to 5A TJ = 25C Min. 3.267 3.234 Typ. 3.3 3.35 0.5 0.1 3 7 1.3 5 6.5 0.7 0.003 72 0.003 0.5 0.5 0.015 Max. 3.333 3.366 6 6 15 20 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % %
TA = 125C
1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
5/18
LD1084 SERIES
ELECTRICAL CHARACTERISTICS OF LD1084#36 (VI=6.6V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA Test Conditions TJ = 25C IO = 0 to 5A VI = 5.2 to 30V (note 1) IO = 0 mA VI = 5.2 to 18V TJ = 25C IO = 0 mA IO = 0 to 5A IO =5 A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, IO = 5A VI = 8.6 3V TA = 25C f =10Hz to 10KHz 60 5.5 0.5 VI = 5.2 to 18V IO = 0 to 5A TJ = 25C Min. 3.564 3.528 Typ. 3.6 3.6 0.5 0.1 3 7 1.3 5 6.5 0.7 0.003 72 0.003 0.5 0.5 0.015 Max. 3.636 3.672 10 10 15 20 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % %
TA = 125C
1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
ELECTRICAL CHARACTERISTICS OF LD1084#5 (VI=8V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA IO = 0 mA IO = 0 mA Test Conditions TJ = 25C VI = 6.6 to 20V VI = 6.6 to 20V TJ = 25C IO = 0 to 5A VI = 6.6 to 30V (note 1) Min. 4.95 4.9 Typ. 5 5 0.5 1 5 10 1.3 5 5.5 0.5 60 6.5 0.7 0.003 72 0.003 0.5 0.5 0.015 Max. 5.05 5.1 10 10 20 35 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % %
IO = 0 to 5A TJ = 25C IO = 0 to 5A IO =5 A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, IO = 5A VI = 10 3V TA = 25C f =10Hz to 10KHz
TA = 125C
1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
6/18
LD1084 SERIES
ELECTRICAL CHARACTERISTICS OF LD1084#8 (VI=11V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA Test Conditions TJ = 25C IO = 0 to 5A VI = 9.6 to 30V (note 1) IO = 0 mA VI = 9.6 to 20V TJ = 25C IO = 0 mA IO = 0 to 5A IO =5 A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, IO = 5A VI = 13 3V TA = 25C f =10Hz to 10KHz 54 5.5 0.5 VI = 9.6 to 20V IO = 0 to 5A TJ = 25C Min. 7.92 7.84 Typ. 8 8 1 2 8 12 1.3 5 6.5 0.7 0.003 71 0.003 0.5 0.5 0.015 Max. 8.08 8.16 18 18 30 60 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % %
TA = 125C
1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
ELECTRICAL CHARACTERISTICS OF LD1084#9 (VI=12V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA Test Conditions TJ = 25C IO = 0 to 5A VI = 10.6 to 30V (note 1) IO = 0 mA VI = 10.6 to 20V TJ = 25C IO = 0 mA IO = 0 to 5A IO =5 A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, IO = 5A VI = 14 3V TA = 25C f =10Hz to 10KHz 54 5.5 0.5 VI = 10.6 to 20V IO = 0 to 5A TJ = 25C Min. 8.91 8.82 Typ. 9 9 1 2 8 12 1.3 5 6.5 0.7 0.003 70 0.003 0.5 0.5 0.015 Max. 9.09 9.18 20 20 30 60 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % %
TA = 125C
1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
7/18
LD1084 SERIES
ELECTRICAL CHARACTERISTICS OF LD1084#120 (VI=15V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA Test Conditions TJ = 25C IO = 0 to 5A VI = 13.6 to 30V (note 1) IO = 0 mA VI = 13.6 to 25V TJ = 25C IO = 0 mA IO = 0 to 5A IO =5 A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, IO = 5A VI = 17 3V TA = 25C f =10Hz to 10KHz 54 5.5 0.5 VI = 13.6 to 25V IO = 0 to 5A TJ = 25C Min. 11.88 11.76 Typ. 12 12 2 4 12 24 1.3 5 6.5 0.7 0.003 66 0.003 0.5 0.5 0.015 Max. 12.12 12.24 25 25 36 72 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % %
TA = 125C
1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
ELECTRICAL CHARACTERISTICS OF LD1084 (VI=4.25V, CI = C O =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO Parameter Output Voltage IO = 10mA Test Conditions TJ = 25C VI = 2.85 to 30V IO = 10mA to 5A (note 1) IO = 10mA VI = 2.85 to 16.5V TJ = 25C IO = 10mA VO Vd IO(min) Isc Load Regulation Dropout Voltage Minimum Load Current Short Circuit Current Termal Regulation SVR IADJ IADJ eN S S Supply Voltage Rejection Adjust Pin Current Adjust Pin Current Change RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability VI = 2.85 to 16.5V TJ = 25C IO = 10mA to 5A IO = 10mA to 5A IO = 5A VI = 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, IO = 5A VI = 4.25V CO = 25 F, CADJ = 25 F, VI = 6.25 3V IO = 10 mA 60 5.5 0.5 Min. 1.237 1.225 Typ. 1.25 1.25 0.015 0.035 0.1 0.2 1.3 3 6.5 0.7 0.003 72 55 0.2 0.003 0.5 0.5 120 5 0.015 Max. 1.263 1.275 0.2 0.2 0.3 0.4 1.5 10 Unit V V % % % % V mA A A %/W dB A A % % %
VO
Line Regulation
IO = 10mA to 5A VI = 2.85 to 16.5V (note 1) TA = 25C f =10Hz to 10KHz
TA = 125C
1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
8/18
LD1084 SERIES
TYPICAL CHARACTERISTICS (unless otherwise specified Tj = 25C, CI=10F (tant.), CO=22F (tant.) Figure 1 : Short Circuit Current vs Dropout Voltage Figure 4 : Output Voltage vs Temperature
Figure 2 : Line Regulation vs Temperature
Figure 5 : Load Regulation vs Temperature
Figure 3 : Quiescent Current vs Temperature
Figure 6 : Quiescent Current vs Output Voltage
9/18
LD1084 SERIES
Figure 7 : Quiescent Current vs Input Voltage Figure 10 : Dropout Voltage vs Temperature
Figure 8 : Dropout Voltage vs Output Current
Figure 11 : Supply Voltage Rejection vs Temperature
Figure 9 : Supply Voltage Rejection vs Output Current
Figure 12 : Supply Voltage Rejection vs Frequency
10/18
LD1084 SERIES
Figure 13 : Adjust Pin Current vs Output Current Figure 16 : Adjust Pin Current vs Temperature
Figure 14 : Reference Voltage vs Temperature
Figure 17 : Line Regulation vs Temperature
Figure 15 : Load Regulation vs Temperature
Figure 18 : Minimum Load Currennt vs Temperature
11/18
LD1084 SERIES
Figure 19 : Supply Voltage Rejection vs Temperature Figure 22 : Supply Voltage Rejection vs Output Current
Figure 20 : Supply Voltage Rejection vs Frequency
Figure 23 : Stability
Figure 21 : Stability
Figure 24 : Line Transient
VI=14 to 15V, IO=200mA,CI = 1F(tant), CO=10F(tant), ts=tf=5s
12/18
LD1084 SERIES
Figure 25 : Line Transient Figure 28 : Line Transient
VI=12 to 13V, IO=200mA, CI = 1F(tant), CO=10F(tant), No CADJ ts=tf=5s
VI=12 to 13V, IO=200mA, CI = 1F(tant), CO=10F(tant), CADJ = 1F ts=tf=5s
Figure 26 : Load Transient
Figure 29 : Load Transient
VI=15 V, I O=0.1 to 5 A, CI = 1F(tant), CO=10F(tant)
VI=13 V, I O=0.1 to 5 A, CI = 1F(tant), CO=10F(tant)
Figure 27 : Load Transient
VI=15 V, I O=0.1 to 5 A, CI = 1F(tant), CO=10F(tant), No CADJ
13/18
LD1084 SERIES
TO-220 MECHANICAL DATA
DIM. A C D D1 E F F1 F2 G G1 H2 L2 L4 L5 L6 L7 L9 DIA. 13.0 2.65 15.25 6.2 3.5 3.75 0.49 0.61 1.14 1.14 4.95 2.4 10.0 16.4 14.0 2.95 15.75 6.6 3.93 3.85 0.511 0.104 0.600 0.244 0.137 0.147 mm. MIN. 4.40 1.23 2.40 1.27 0.70 0.88 1.70 1.70 5.15 2.7 10.40 0.019 0.024 0.044 0.044 0.194 0.094 0.393 0.645 0.551 0.116 0.620 0.260 0.154 0.151 TYP MAX. 4.60 1.32 2.72 MIN. 0.173 0.048 0.094 0.050 0.027 0.034 0.067 0.067 0.203 0.106 0.409 inch TYP. MAX. 0.181 0.051 0.107
P011C
14/18
LD1084 SERIES
D2PAK MECHANICAL DATA
mm. DIM. MIN. A A1 A2 B B2 C C2 D D1 E E1 G L L2 L3 M R V2 0 4.88 15 1.27 1.4 2.4 0.4 8 0 10 8.5 5.28 15.85 1.4 1.75 3.2 0.192 0.590 0.050 0.055 0.094 0.016 8 4.4 2.49 0.03 0.7 1.14 0.45 1.23 8.95 8 10.4 0.393 0.335 0.208 0.624 0.055 0.068 0.126 TYP MAX. 4.6 2.69 0.23 0.93 1.7 0.6 1.36 9.35 MIN. 0.173 0.098 0.001 0.027 0.044 0.017 0.048 0.352 0.315 0.409 TYP. MAX. 0.181 0.106 0.009 0.036 0.067 0.023 0.053 0.368 inch
P011P6G
15/18
LD1084 SERIES
D2PAK/A MECHANICAL DATA
mm. DIM. MIN. A A1 B B2 C C2 D E G L L2 4.40 2.49 0.7 1.14 0.45 1.21 8.95 10 4.88 15 1.27 TYP MAX. 4.60 2.69 0.93 1.7 0.60 1.36 9.35 10.4 5.28 15.85 1.4 MIN. 0.173 0.098 0.027 0.044 0.017 0.047 0.352 0.393 0.192 0.590 0.050 TYP. MAX. 0.181 0.106 0.036 0.067 0.023 0.053 0.368 0.409 0.208 0.106 0.055 inch
16/18
LD1084 SERIES
Tape & Reel D2PAK-P 2PAK-D 2PAK/A-P 2PAK/A MECHANICAL DATA
mm. DIM. MIN. A C D N T Ao Bo Ko Po P 10.50 15.70 4.80 3.9 11.9 10.6 15.80 4.90 4.0 12.0 12.8 20.2 60 14.4 10.70 15.90 5.00 4.1 12.1 0.413 0.618 0.189 0.153 0.468 0.417 0.622 0.193 0.157 0.472 13.0 TYP MAX. 180 13.2 0.504 0.795 2.362 0.567 0.421 0.626 0.197 0.161 0.476 0.512 MIN. TYP. MAX. 7.086 0.519 inch
17/18
LD1084 SERIES
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. (c) The ST logo is a registered trademark of STMicroelectronics (c) 2003 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. (c) http://www.st.com
18/18

▲Up To Search▲

Price & Availability of LD1084

	To Download LD1084 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .